FibeAir IP features a powerful, integrated Ethernet switch for advanced networking solutions and an optional TDM cross-connect for nodal site applications. Tx Range (Manual/ATPC). 20dB dynamic range. System Specifications. FibeAir® IP Technical. Introducing FibeAir IP FibeAir IP is Ceragon’s next. March Reuven Ginat Describes the FibeAir IPE CLH Compact This manual is intended for use by Ceragon customers, potential customers.
|Published (Last):||19 March 2009|
|PDF File Size:||6.7 Mb|
|ePub File Size:||7.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
Single Point Stud Grounding Wire 1. Post on Apr views. Inspection Check the packing lists, and ensure that the correct part numbers and quantities of components arrived.
Tue 28 Nov – A readily accessible Listed branch circuit overcurrent protective device, rated 15 A, must ecragon incorporated in the building wiring. All operators and site owners have specific requirements regarding the grounding of installations. Unpack the contents and check for damaged or missing parts. If the management station is located a t a remote site Network Ceargon Centerverify that the management station can manage the link and receive traps. Power off drawer V on that end and power on drawer H.
This document is provided as is, without warranty of any kind. Remove the current fan tray by releasing the safety mnaual and removing the tray.
Power-Supply is properly grounded DC power backup type: The same antenna type integrated as indicated above can be used recommended. The purpose of the commissioning tests is to verify correct and proper operation of the product.
This will give you the current IP address. Easily accessible, but only by authorized personnel. All other user terminations are secure and correctly terminated. The purpose of the commissioning tests is to verify correct and proper operation of the product.
Align the antennas, one at a time, until expected RSL is achieved. However, at sites with multiple installations, correct and adequate labeling is essential for future maintenance operations. The purpose of this procedure amnual to verify correct installation and operation of the installed link and the interoperability with customer end equipment.
Note that cable length difference should not exceed 10 meters. Select Add on the Users section and enter anonymous in the Manua, user Account window.
Ceragon IP-10 IDU CLI Commands List
Ceragon’s Acceptance and Commissioning procedure includes the following stages: That s it you are done. These interfaces are designed ceragn use as intra-building interfaces only and require isolation from the exposed OSP cabling.
As with any type of construction, a local permit may be required before installing an antenna. The RFU polarization is as per link requirements and matches the polarization of the antenna.
Flexible bandwidth sharing between the TDM and Ethernet traffic ensures optimal throughput for all your media transfer needs.
CONOCIENDO RADIO CERAGON IP10 by Reynaldo Gutierrez Delgado on Prezi
Mounting Pole is of sufficient height, and is safely positioned, so as not to cause a safety hazard. Note about Heat Dissipation: If the management station is located at a remote site Network Operation Centerverify that the management station can manage the link and receive traps. Remove the sticker from the RFU-C antenna interface. Ceragno the drawers respectively. However, at sites amnual multiple installations, correct and adequate labeling is essential for future maintenance operations.
Antenna Water Drain Plugs are fitted and removed, where appropriate. The site should be accessible to certified personnel only. Vertical Pi Horizontal Pole2. Following this procedure will ensure proper, long-lasting, and safe operation of cergon product. All steelwork is Galvanized or Stainless Steel, as appropriate to prevent corrosion. The purpose of these plugs is to allow any moisture that forms on the inside of the antenna or radome to drip out and prevent a pool within the antenna.
Ceragon FibeAir-IP10 Manual
Defining a TDM Trail. Ne pas essayer de rgler le courant de commande du laser. Spread grease on the O-ring supplied with the flexible waveguide. No more than m from RFU location. This equipment is designed to permit connection between the earthed conductor of the DC supply circuit and the earthing conductor at the equipment.
To find out more, including how to control cookies, see here: Interoperability VerificationConnect customer end equipment to the line interfaces, and verify correct operation.